Cisco ENARSI 300-410 is short for Cisco 300-410 Implementing Cisco Enterprise Advanced Routing and Services Certification Exam. The 300-410 exam is part of the Cisco CCNP exam category and is one of the most popular certification exams. Lead4Pass 300-410 dumps is the most trusted exam certification study preparation program. Check the latest updated 300-410 dumps U2022.3 from Lead4Pass, The latest version is the most practical and effective exam material after revision and update, ensuring that you successfully pass the Cisco ENARSI 300-410 exam the first time.
Check out the latest Cisco ENARSI 300-410 dumps U2022.3 below:
In addition, we have Cisco ENARSI 300-410 Free Dumps, which is part of the updated 300-410 dumps for inspection.
PS. Participate in the check and finally verify the answer
QUESTION 1
Refer to the exhibit.
When the FastEthemet0/1 goes down, the route to 172.29.0.0/16 via 192.168.253.2 is not installed in the RIB, Which
Does action resolve the issue?
A. Configure feasible distance greater than the successor\’s feasible distance.
B. Configure reported distance greater than the successor\’s feasible distance.
C. Configure feasible distance greater than the reported distance.
D. Configure reported distance greater than the feasible distance.
QUESTION 2
Refer to the exhibit.
R2 has two paths to reach 192.168.13.0/24. but traffic is sent only through R3. Which action allows traffic to use both
paths?
A. Configure the bandwidth 2000 command under interface FastEthernet0/0 on R2.
B. Configure the variance 4 commands under the EIGRP process on R2.
C. Configure the delay 1 command under interface FastEthernet0/0 on R2.
D. Configure the variance 2 commands under the EIGRP process on R2
From the output of the “show IP eigrp topology …” command, we notice network 192.168.13.0/24
was learned via two routes:+ From 192.168.23.3 (R3) with FD = 1075200 and AD = 281600+ From 192.168.12.1 (R1) with FD = 2611200 and AD = 281600 From the output of the “show IP route …”
command, we learned that the best (and chosen) path is via 192.168.23.3 (R3).
To use both paths (called unequal cost load balancing) with EIGRP, the second path via R1 must satisfy the feasibility condition. The feasibility condition states that the Advertised Distance (AD) of a route must be lower than the feasible distance of the current successor route.
In this case, the second path satisfies the feasible condition as its AD (281600) is smaller than the FD (1075200) of the best path. Therefore we can configure load balancing with the “variance” command.
In other words, EIGRP will install all paths with metric / best_metric =
2611200 / 1075200 =2.4.
So with a variance greater than 2 (and must be an integer), we can load balance traffic to network 192.168.13.0/24.
QUESTION 3
What is a characteristic of Layer 3 MPLS VPNs?
A. Traffic engineering capabilities provide QoS and SLAs.
B. Traffic engineering supports multiple IGP instances.
C. LSP signaling requires the use of unnumbered IP links for traffic engineering.
D. Authentication is performed by using digital certificates or preshared keys.
QUESTION 4
Which mechanism must be chosen to optimize the reconvergence time for OSPF at company location 408811049 that
is fewer CPU-intensive than reducing the hello and dead timers?
A. SSO
B. BFD
C. Dead Peer Detection keepalives
D. OSPF demand circuit
QUESTION 5
Refer to the exhibit. An engineer is trying to block the route to 192.168.2.2 from the routing table by using the
configuration that is shown. The route is still present in the routing table as an OSPF route. Which action blocks the
route?
A. Use an extended access list instead of a standard access list.
B. Change sequence 10 in the route-map command from permit to deny.
C. Use a prefix-list instead of an access list in the route map.
D. Add this statement to the route map: route-map RM-OSPF-DL denies 20.
QUESTION 6
Refer to the exhibit. The DHCP client is unable to receive an IP address from the DHCP server. RouterB is configured
as follows:
Which command is required on the FastEthernet 0/0 interface of RouterB to resolve this issue?
A. RouterB(config-if)#lp helper-address 172.31.1.1
B. RouterBiconfig-ififclp helper-address 255.255 255 255
C. RouterB(config-if)#lp helper-address 172.16.1.1
D. RouterB(config-if)#lp helper-address 172.16.1.2
QUESTION 7
Refer to the exhibit.
Which two commands provide the administrator with the information needed to resolve the issue? (Choose two.)
A. debug SNMP packet
B. debug SNMP engine-id
C. show SNMP user
D. debug snmpv3 engine-id
E. show snmpv3 user
QUESTION 8
Refer to the exhibit. Troubleshoot and ensure that branch B only ever uses the MPLS B network to reach HQ. Which
Does action achieve this requirement?
A. Introduce an AS path filter on branch A routers so that only local prefixes are advertised into BGP
B. increase the local preference for all HQ prefixes received at branch B from the MPLS B network to be higher than the
local preferences used on the MPLS A network
C. Introduce AS path prepending on the branch A MPLS B network connection so that any HQ advertisements from
branch A toward the MPLS B network is prepended three times
D. Modify the weight of all HQ prefixes received at branch B from the MPLS B network to be higher than the weights
used on the MPLS A network
If we modify the weight, increase local preference, or use AS path prepending then we can only make MPLS B prefer over MPLS A.
But when MPLS B is down then MPLS A will be used which does not meet the requirement of this question. Only with AS path filtering we can deny prefixes from certain AS and make sure branch B never uses MPLS A to reach HQ.
QUESTION 9
Refer to the exhibit.
Redistribution is enabled between the routing protocols, and nowPC2 PC3 and PC4 cannot reach PC1. What are the
two solutions to fix the problem? (Choose two.)
A. Filter RIP routes back into RIP when redistributing into RIP in R2
B. Filter OSPF routes into RIP from EIGRP when redistributing into RIP in R2
C. Filter all routes except RIP routes when redistributing into EIGRP in R2.
D. Filter RIP AND OSPF routes back into OSPF from EIGRP when redistributing into OSPF in R2
E. Filter all routes except EIGRP routes when redistributing into OSPF in R3.
Even PC2 cannot reach PC1 so there is something wrong with RIP redistribution in R2. Because RIP has higher
Administrative Distance (AD) value than OSPF and EIGRP so it will be looped when doing mutual redistribution.
QUESTION 10
Refer to the exhibit. A network administrator is troubleshooting the OSPF adjacency issue by going through the console
logs in the router, but due to an overwhelming log messages stream, it is impossible to capture the problem. Which two
commands reduce console log messages to relevant OSPF neighbor problem details so that the issue can be resolved?
(Choose two.)
A. debug condition OSPF neighbor
B. debug condition interface
C. debug condition session-id ADJCHG
D. debug condition all
QUESTION 11
Refer to the exhibit.
The administrator configured route advertisement to a remote low resources rooter to use only the default route to reach
any network but failed. Which action resolves this issue?
A. Change the direction of the distribute-list command from out to in.
B. Remove the line with the sequence number 5 from the prefix-list.
C. Remove the prefix keyword from the distribute-list command.
D. Remove the line with the sequence number 10 from the prefix-list.
QUESTION 12
An engineer configured a Cisco router to send reliable and encrypted notifications for any events to the management
server. It was noticed that the notification messages are reliable but not encrypted. Which action resolves the issue?
A. Configure all devices for SNMPv3 informs with auth.
B. Configure all devices for SNMPv3 informs with priv.
C. Configure all devices for SNMPv3 traps with auth.
D. Configure all devices for SNMPv3 traps with priv.
SNMP notifications can be sent as traps or inform requests. Traps are unreliable because the receiver does not send acknowledgments when this device receives traps.”Send reliable and encrypted notifications for any events” so it is SNMP notifications. For encryption, we need to configure “priv”.
Verify the answer:
| Q1 | Q2 | Q3 | Q4 | Q5 | Q6 | Q7 | Q8 | Q9 | Q10 | Q11 | Q12 |
| C | B | A | B | B | D | AC | D | AB | AB | B | B |
Cisco ENARSI 300-410 Free Dump Question, Share Using PDF:https://drive.google.com/file/d/1hltskWXFFxr6iERMxHxRjGglPQ1Zm-ja/view?usp=sharing
The latest version of Cisco ENARSI 300-410 Dumps U2022.3 is modified, updated, and works. Using Cisco ENARSI 300-410 Dumps U2022.3: https://www.leads4pass.com/300-410.html. Helping you pass the 300-410 Implementing Cisco Enterprise Advanced Routing and Services exam with ease.